JUST HOW TO INSTALL A BATHTUB ( GUIDE).

Just how to Install a Bathtub ( Guide).

Just how to Install a Bathtub ( Guide).

Blog Article

Quote

The content which follows on the subject of How to Install a Bathtub Yourself is truly enlightening. Don't skip it.


Installing A Bathtub
Setting up a bathtub isn't exactly rocket science, but it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult project. If the old bathtub is conveniently obtainable, the job can move quickly; if you have to open a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the new one. Make certain you have qualified yourself for the task and are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed job, it is much better to think about employing one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will help you mount a brand-new tub in your restroom if you have currently gotten a new tub and also don't need to transform the setup of your previous water system pipes.
Your devices and also material checklist need to make up the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you require to change old taps with new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather bothersome because of the limited gain access to that is usually the situation.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have actually been removed, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this process. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
    Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.

    Suitable New Touches


    If the tails of the new taps are plastic, after that you will certainly require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and the other end gives a connection to the existing supply pipelines.
    If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the tap in position with the supplier given backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former kind ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Installing the Bathtub


    Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little points.
    The next goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the bathtub up until the level checks out level.
    To set up taps, fit the bottom of the outermost adaptable faucet adapter to the suitable supply pipe by making a compression join; then do the very same for the various other tap.
    Turn on the supply of water and check all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as likewise inspect the overflow outlet and also the regular electrical outlet for leakages.
    Ultimately, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at least when as this will certainly resolve it into its final placement.

    Planning for the Installment


    First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
    Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
    Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall between the bath as well as the tiling, bring about problems with moisture and also possible leaks to the ceiling below.
    You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split relatively very early if you do not take into account this movement before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is advisable to fit the tiles using water-resistant or waterproof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    Do you enjoy more info about A Step-by-Step Guide to Installing a Bathtub? Post a review below. We'd be pleased to hear your opinion about this blog entry. Hoping that you come back again soon. Remember to set aside a second to distribute this article if you enjoyed it. Kudos for your time. Don't hesitate to stop by our website back soon.



    Estimate Free

    Report this page